all Models - PLEASE PROVIDE VIN# IN SHIPPING INSTRUCTIONS BOX WHEN ORDERING.Article code: v.nr.1137500084

Article code: v.nr.1137580005

LARGE all Models MAIN MAT COVERS MOST OF TRUNK FLOOR. ANTHRACITE GRAY/BLACK ORIGINAL COLOR. FOR SMALL MAT UNDER SPARE TIRE, SEE # 68-2053.Article code: v.nr.1136840104

SMALL all Models MAT MAINLY UNDER SPARE TIRE. FOR LARGE MAIN MAT, SEE # 68-2052.Article code: v.nr.1136840604

Article code: v.nr.1137500077

Article code: v.nr.1136110139

Article code: v.nr.1136100826

all ModelsArticle code: v.nr.1137580058

Front Subframe to Leaf Spring Sleeve All W113 Pagoda models from 1963 to 1971

Article code: v.nr.0004620923

Article code: v.nr.0004621023

UNDER DASH PANEL SET W113 230SL 250SL (EARLY)

UNDER DASH PANEL SET W113 250SL 280SL (LATE)

UPPER OUTER ARM KIT

SPECIFY LEFT, RIGHT OR BOTH WHEN ORDERING

MAIN LINK ROD ONLY

UPPER SHIFT COVER SEAL

URETHANE FRONT SWAY BAR TO FRAME QTY NEEDED PER CAR MODEL   W108 (250/280) W109 (300/6.3) W110 (190/200/230) W111 (220/250/280) W112 (300) W113 (230/250/280SL) Front sway bar to frame - 22mm        2 2 early 2 late Front sway bar to frame - 23.85mm   2     2 late    Front sway bar to frame - 20.34mm     2 2 early   2 late NOTE: Before selecting a front sway bar frame bushing, please measure the bar diameter first.   Use either a flexible tape or a pair of calipers as shown. Do not use a flat ruler.   With Calipers  With flexible tape If using an inch tape – take measurement and divide by 3.142 to get the diameter. To convert from inches to mm, simply multiply by 25.4. In both cases, this sway bar measures 24mm.

URETHANE FRONT LEAF SPRING BUSHING QTY NEEDED PER CAR MODEL W108 (250/280) W110 (190/200/230) W111 (220/250/280) W113 (230/250/280SL) 4 4 4 4

URETHANE FRONT LEAF SPRING BUSHING QTY NEEDED PER CAR MODEL W109 (300/6.3) W112 (300) 4 4

URETHANE TRAILING ARM REAR (TO AXLE) QTY NEEDED PER CAR MODEL SOLD PER BUSHING SLEEVE NOT SOLD SEPERATELY W108 (250/280) W109 (300/6.3) W110 (190/200/230) W111 (220/250/280) W112 (300) W113 (230/250/280SL)   4     4  

This part is for all USA headlight assemblies.Article code: v.nr.1138201261

Article code: v.nr.0001581435

HOSE SOLD IN METER LENGTHS, PLEASE STATE CHASSIS # IN SHIPPING INSTRUCTIONS BOX WHEN ORDERINGArticle code: v.nr.0004352182

Late 280SL HOSE WITH FITTED ENDS AND CHECK VALVE. For 280SL FROM CHASSIS # 011948 TO PRODUCTION END. EARLIER HOSE WITH 90 DEGREE ENDS IS NO LONGER AVAILABLE.Article code: v.nr.1134300629

RUBBER GASKET/SEAL FOR BETWEEN VALVE COVER AND CYLINDER HEAD.Article code: v.nr.1300160221

VALVE COVER TUBE - PLASTIC 230SL — Chassis 113.042       1963 - 1966 Base Convertible 2.3L L6 250SE — Chassis 111.023       1966 - 1967 Base Convertible 2.5L L6 250SE — Chassis 108/111       1966 - 1967 Base Coupe 2.5L L6 250SL — Chassis 113.043       1967 Base Convertible 2.5L L6 280SE — Chassis 108/111       1968 - 1969 Base All 2.8L L6

BRASS OR COPPER GUIDE IN CYLIDER HEAD FOR INTAKE VALVE. STANDARD SIZE 14X9X55. 6 PER CAR.Article code: v.nr.1300500024

BRASS OR COPPER GUIDE IN CYLINDER HEAD FOR INTAKE VALVES. REPAIR SIZE OF +.001 OVER STANDARD 14mm O.D. LARGER REPAIR SIZES ARE AVAILABLE UPON SPECIAL REQUEST.Article code: v.nr.1300500124

Article code: v.nr.1210500624

Article code: v.nr.1210501624

BRASS OR COPPER GUIDE IN CYLIDER HEAD FOR INTAKE VALVE. STANDARD SIZE 14X9X55. 6 PER CAR.

HALF MOON SHAPED COLLET TO RETAIN INTAKE & EXHAUST VALVE AT TOP SHAFT POINT OF VALVE. FOR 250 & 280SL, 2 PER VALVE, 24 PER CAR. WILL NOT FIT 230SL.Article code: v.nr.1150530026

HALF MOON SHAPED COLLET TO RETAIN INTAKE & EXHAUST VALVES AT TOP SHAFT SIDE OF VALVE. 230SL ONLY, 2 PER VALVE, 24 PER CAR.Article code: v.nr.1800530627

VALVE STEM - METAL

FOR 230SL ONLY.Article code: v.nr.1275860105